Question 1

Dimensions locating target areas are ____________________ and are enclosed in a rectangular frame.

Accepted Answer

The answer of Dimensions locating target areas are ____________________ and...

Question 2

The datum-target symbol contains the target area size (where applicable), the datum identifying letter, and the ______________________________.

Accepted Answer

target number

Question 3

The symbol for a datum target point is ____.

Accepted Answer

A)   
B)   
C)   
D)   E) A) and C)
F) A) and B)

Question 4

The symbol for a datum target line is ____.

Accepted Answer

A)   
B)   
C)   
D)   E) All of the above
F) A) and C)

Question 5

Points, lines, and areas on datum features are designated on a drawing by means of a ____.

Accepted Answer

A)   target symbol
B)   datum symbol
C)   datum-target symbol
D)   basic dimensionE) A) and B)
F) All of the above

Question 6

The datum-target symbol is approximately ____________________ times the height of lettering on the drawing.

Accepted Answer

The answer of The datum-target symbol is approximately ____________________ times...

Question 7

For flat surfaces, ____ target points or areas are required for a primary datum.

Accepted Answer

A)   one
B)   two
C)   three
D)   fourE) A) and B)
F) A) and C)

Question 8

The symbol  on an edge view of a surface tells you that the line is a _________________________.

Accepted Answer

The answer of The symbol  on an edge view...

Question 9

For greater accuracy, datum targets should be placed as far apart as possible.

Accepted Answer

A) True 
 B)False

Question 10

When the length of a datum target line must be controlled, its length and location are dimensioned.

Accepted Answer

A) True 
 B)False  True

Question 11

When targets are used for the primary datum, they must also be used for secondary and tertiary datums.

Accepted Answer

A) True 
 B)False  False

Question 12

There are instances where it is acceptable to use only a portion of a feature as a datum feature.

Accepted Answer

A) True 
 B)False

Exam 42: Datum Targets

Dimensions locating target areas are ____________________ and are enclosed in a rectangular frame.

Correct Answer
verified

The datum-target symbol contains the target area size (where applicable), the datum identifying letter, and the ______________________________.

Correct Answer
verified
target number

The symbol for a datum target point is ____.

Correct Answer
verified

The symbol for a datum target line is ____.

Correct Answer
verified

Points, lines, and areas on datum features are designated on a drawing by means of a ____.

Correct Answer
verified

The datum-target symbol is approximately ____________________ times the height of lettering on the drawing.

Correct Answer
verified

For flat surfaces, ____ target points or areas are required for a primary datum.

Correct Answer
verified

The symbol on an edge view of a surface tells you that the line is a _________________________.

Correct Answer
verified

For greater accuracy, datum targets should be placed as far apart as possible.

Correct Answer
verified

When the length of a datum target line must be controlled, its length and location are dimensioned.

Correct Answer
verified
True

When targets are used for the primary datum, they must also be used for secondary and tertiary datums.

Correct Answer
verified
False

There are instances where it is acceptable to use only a portion of a feature as a datum feature.

Correct Answer
verified

Exam 42: Datum Targets

Dimensions locating target areas are ____________________ and are enclosed in a rectangular frame.

Correct AnswerverifiedShow Answer

The datum-target symbol contains the target area size (where applicable), the datum identifying letter, and the ______________________________.

Correct Answerverifiedtarget number

The symbol for a datum target point is ____.

Correct AnswerverifiedShow Answer

The symbol for a datum target line is ____.

Correct AnswerverifiedShow Answer

Points, lines, and areas on datum features are designated on a drawing by means of a ____.

Correct AnswerverifiedShow Answer

The datum-target symbol is approximately ____________________ times the height of lettering on the drawing.

Correct AnswerverifiedShow Answer

For flat surfaces, ____ target points or areas are required for a primary datum.

Correct AnswerverifiedShow Answer

The symbol on an edge view of a surface tells you that the line is a _________________________.

Correct AnswerverifiedShow Answer

For greater accuracy, datum targets should be placed as far apart as possible.

Correct AnswerverifiedShow Answer

When the length of a datum target line must be controlled, its length and location are dimensioned.

Correct AnswerverifiedTrue

When targets are used for the primary datum, they must also be used for secondary and tertiary datums.

Correct AnswerverifiedFalse

There are instances where it is acceptable to use only a portion of a feature as a datum feature.

Correct AnswerverifiedShow Answer

Correct Answer
verified

Correct Answer
verified
target number

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
True

Correct Answer
verified
False

Correct Answer
verified